Winchester Ammunition 1300 Bedienungsanleitung

Winchester®Model 1300 Owner’s ManualLicensee

8Avoid applying too much oil. Only a light film is necessary. Excessive oil should be wiped off, especially in cold weather.CLEANING PARTS WITH SPECIA

9• “OFF SAFE” — The safety button is pushed fully to theleft (Figure 4). A large red band is exposed on the buttonas it protrudes on the left side of

103. Slide the barrel rearward. 4. Guide the barrel bracket over the end of the magazinetube and guide the barrel extension into the receiver.Be sure

111. Depress the disconnector release button found behindthe trigger guard on the left side. This unlocks theaction without releasing the hammer.2. Op

5. When the last shell in the magazine has been cycledthrough the chamber and out the ejection port, leavethe action open.6. Using your index finger,

132. Pull the forearm fully rearward until the fired shell isejected out the ejection port. 3. Push the forearm fully forward, transferring a new shel

YOUR MODEL 1300 SHOTGUN. CAUTION: WHENEVER HANDLING ANY SHOTGUN FOR THEPURPOSE OF REMOVING OR INSTALLING A CHOKE TUBE,MAKE ABSOLUTELY CERTAIN THE GUN

4. Using your fingers, screw the appropriate tube into themuzzle end of the barrel, tapered end first, knurled endoutward. When it becomes finger tigh

oil the threads inside the barrel, as well as on the choketube itself. This will protect the threads from being damaged, and also prevent dirt build u

173. Slowly raise your hand and let the magazine springrelax. Capture the parts in your hand as they spring out.4. With the spring relaxed, the fricti

Important instructions for Winchester®Model 1300 ShotgunsCustomer Service Department (United States)Winchester Firearms275 Winchester AvenueMorgan, Ut

IS POINTED IN A SAFE DIRECTION. PLACE THE SAFETY INTHE “ON SAFE” POSITION.UPORDOWN ELEVATION ADJUSTMENTS —Adjusting elevation on your Model 1300 requi

WARNING: YOUR WINCHESTER SHOTGUN IS DRILLEDAND TAPPED FOR THE MOUNTING OF BASES AND RINGSTO ACCOMMODATE AN APPROPRIATE SCOPE OR SIGHT.ALWAYS USE THE C

8. Tighten the screws snugly, but do not overtighten.9. Mount your scope rings and scope as outlined in theinstructions supplied with your scope rings

WEAR EYE PROTECTION AT ALL TIMES. NEVER DISASSEMBLE BEYOND WHAT IS EXPLAINED ANDSHOWN IN THIS OWNER’S MANUAL.Disassembling the action can be done in t

6. Push the pin through sufficiently until it can be graspedwith your fingers. Pull it the rest of the way out. If itcannot be removed with fingers, m

23up on the slide arm bridge and disengage the curved tongue on the slide arm bridge from the groove in the firing pin. This will detach the slide arm

7. Remove the magazine cap and carefully guide the slidearms and bolt/slide arm bridge assemblies into the frontof the receiver. As the assemblies ent

necessary to slide the forearm into different positions until the trigger guard group fits flush into the receiver.When properly installed it will fit

CLEANING PROCEDURES —ALWAYS PLACE THE SAFETY IN THE “ON SAFE” POSITION BEFORE BEGINNING ANY CLEANING PROCEDURE AND BE CERTAIN YOUR GUN’S CHAMBER AND M

8. When transporting only, store your Model 1300 in aquality protective case to prevent scratches and dents.Store in a dry place to prevent corrosion.

GUN SAFETY WARNINGSIT IS ESSENTIAL THAT THESE OPERATING INSTRUCTIONSBE THOROUGHLY STUDIED BEFORE USING THIS FIREARMTO ASSURE PROPER AND SAFE GUN HANDL

GENERAL PRODUCT AND HISTORICAL QUESTIONS —Winchester Firearms275 Winchester AvenueMorgan, UT 84050-93331-800-945-5237 (toll free)PARTS, SERVICE, REPAI

29NOTES

30NOTES

31NOTES

Winchester Firearms275 Winchester AvenueMorgan, UT, U. S. A. 84050-9333www.winchesterguns.comLicenseeLicenseeWinchester trademarks licensed from Olio

28. Keep barrel, chamber and action free of rust. Rust inthe barrel and chamber can cause excessive pressuresresulting in serious injury. A rusted, pi

3begin your pumping action. You’ll soon find that you willcomplete the pumping action forward quickly and withoutconscious effort. In a brief instant

WinChoke®SystemMuzzle Sight BeadMagazine CapForearmMagazine Disconnector Release Button (Reverse Side) Trigger GuardRecoil PadReceiverEjection PortVen

5PRESSURES IN EXCESS OF SAAMI (SPORTING ARMS AND AMMUNITION MANUFACTURERS’ INSTITUTE) ESTABLISHED STANDARDS.DISCHARGING FIREARMS IN POORLY VENTILATED

6The advanced, high-strength alloyreceiver is much lighter than steel.The rugged rotary bolt design engagesthe barrel extension instead of the topof t

FIGURE 37Choice of barrels. Choose standard ventilated rib models with theWinChoke®system; rifled barrels with rifle sights for shooting slugs;smoothb